CHEVY NOMAD FULL

CHEVY NOMAD FULL

Holding all of this rolling stock up is a full set of Schott Mach V wheels measuring 18×8 and 18×9 all wrapped in Nitto NT555 rubber measuring 225/45ZR18 and 275/40ZR18. The difference resides in the fact the 4L70E is a stronger unit (has five-pinion gearsets, heat-treated stator shaft splines, induction-hardened turbine shaft, seven-plate clutch, and specific valvebody calibration) and comes with an input shaft speed sensor.

It should be noted that the 4L70E trans offers virtually no outward difference between the 4L60E, 4L80E, and the last run of the 700-R4. Accompanying the header package is an ARP 12-point stainless steel header bolt kit, a pair of matching Cometic HTS header and HTS collector gaskets (if needed). Made from cast 321 stainless steel flanges along with the tight radius cast 321 stainless steel elbows allows for large tube exhaust manifolds in tight places and the header is also lightweight compared to other options. Made specifically for the AME Tri-Five chassis with an LS swap, a special set of long-tube headers is available. More on the exhaust from Ultimate Headers. (To make this swap yourself you might also think about a “muscle car oil pan” that’s available from several sources, such as Classic Performance Products, to work with your earlier tin.) To bump the power up to 495 hp and 475 lb-ft of torque the motor was equipped with a multi-port injection, K&N air filter, a Powermaster alternator, an MSD starter, a SPAL electric fan, a custom-fabricated exhaust system by MetalWorks based on 2-1/2-inch tubing that runs back to a pair of Flowmaster 50-series mufflers.

Accompanying is a high-lift, hydraulic roller camshaft bringing the base motor to 430 hp. The V-8 is fitted with L92-type heads delivering 10.7:1 compression. Settled between the AME ’rails is a crate motor powerplant initially found in the fifth-gen Camaro SS and C6 Corvette LS3 6.2L (376 cubes) V-8 direct from Chevrolet Performance. Getting all of the braking to respond falls to a Wilwood master cylinder and Lokar pedals. Looking in the back you will see more Wilwood 12-inch rotors and Dynalite calipers, Strange coilovers, packaged around a Strange 9-inch rearend, and 31-spline axles spun by the 3.70 gears. There’s also an AME 1-1/8-inch front sway bar, Strange coilover shocks, and a Detroit Speed power rack-and-pinion steering. It has an IFS that’s wrapped around Wilwood spindles, 12-inch drilled-and-slotted rotors, and Dynalite four-piston calipers that are powdercoated in red. During the conversation it was decided that in order to get the job done the original chassis (frame and suspension) would have to be parked in a corner and a new chassis put in its place.Īn Art Morrison Enterprises (AME) GT Sport chassis was placed beneath the Chevrolet Nomad sheetmetal. Powell knew Tom wanted a real hot rod, since the Nomad was sans original engine and transmission there was little reason not to go fully modern. Once the body was dipped, to get rid of decades-old baddies, he spoke with shop manager Matt Powell of MetalWorks on a course of action. It didn’t take Tom long to realize the type of car he wanted was outside the scope of his skill sets. It was now time to begin the build in earnest. From this auspicious beginning it would eventually end up in a used car parking lot in Sacramento area back in 1996 and that’s when its next life began. (All of us have or will be there someday.) According to the VIN the Nomad was an original California car built in Oakland around December 15, 1955. He purchased the car from a hobbyist who finally one day admitted he had one too many projects. He settled in on this particular 1956 Chevy Nomad because it was straight, it was complete, and it was rust-free-he hit the trifecta for any of us building vintage tin. In the meantime, he spent his time looking for just the right Nomad to launch his dream project. Time passes and dreams are doggedly worked on, no matter how much time it takes, and Tom was able to begin this build back in the summer of 2001. Tom tells us that he first joined the Classic Chevy Club back in 1977 and was a member for many years. Apparently dreams do come true, as Tom now has this beautiful 1956 Chevy Nomad from the shop of MetalWorks Classic Auto Restoration in Eugene, Oregon. Tom Morehouse of Klamath Falls, Oregon, is no different than thousands of other hot rodders-he has spent a lifetime dreaming about owning a Nomad. Many of us have lifelong dreams on what our ideal hot rod should be.

Chevy nomad